How do you change a headlamp bulb front passengers side on an Audi A6 2.4 SE 2002?
Answers:
Headlights, servicing
Headlight bulbs, replacing
Low beam bulb (halogen headlight), replacing
Removing
‒ For right headlight, remove rear part of air intake duct.
‒ Remove cover from headlight housing.
‒ → Remove connector -2- for low beam bulb.
‒ Remove wire clamp -1- and take bulb out of housing.
Installing
‒ Install new bulb in housing.
CAUTION!
Do not touch the glass part of the bulb with bare hands.
‒ Secure base of bulb with wire clamp.
‒ Reinstall connector and install cover on headlight housing.
‒ Secure cover on housing with wire retainers.
Low beam bulb (high intensity gas discharge lamp), replacing
WARNING! HIGH VOLTAGE!
◆ Before working on components marked with yellow high voltage symbols, be sure to disconnect the battery after determining the correct coding for the anti-theft radio.
Removing
‒ For right headlight, remove rear part of air intake duct.
‒ Remove cover from headlight housing.
‒ → Disconnect electrical connector -1- for gas discharge bulb by turning it counterclockwise.
‒ Remove retainer -2- on gas discharge bulb by turning it counterclockwise.
‒ Remove bulb.
Installing
‒ → Install retainer -1- on lugs of gas discharge bulb -3- and insert with both notches (arrows). Now secure by turning clockwise.
‒ Connect electrical connector and reinstall cover on headlight housing.
Igniter for gas discharge lamp -N195-, removing and installing
WARNING! HIGH VOLTAGE!
◆ Before working on components marked with yellow high voltage symbols, be sure to disconnect the battery after determining the correct coding for the anti-theft radio.
Removing
‒ Remove cover for headlight housing.
‒ → Disconnect electrical connector -1- for gas discharge bulb- by turning it counterclockwise.
‒ → Loosen grommet -1- in headlight cover by pushing down on lugs, (arrows).
‒ Now guide connector for gas discharge bulb through opening of cover.
‒ → Disconnect electrical connector -1- from igniter for high intensity gas discharge lamp.
‒ Remove bracket -2- for igniter by removing screw (arrow).
‒ Remove igniter from housing.
Installing
‒ Install in reverse order of removal.
High beam bulb, removing and installing
Removing
‒ For right headlight, remove rear part of air intake duct.
‒ Remove cover from headlight housing.
‒ → Disconnect connector -1-.
‒ Disengage wire clamp -2- and remove bulb from housing.
Installing
‒ Install new bulb in housing.
CAUTION!
Do not touch the glass part of the bulb with bare hands.
‒ Secure base of bulb with wire clamp.
‒ Reconnect electrical connectors and install cover on headlight housing.
‒ Secure cover with wire retainers.
Turn signal light bulb, removing and installing
Removing
‒ For right headlight, remove rear part of air intake duct.
‒ Remove cover from headlight housing.
‒ → Turn bulb holder -1- counterclockwise and pull it from housing.
Installing
‒ Install in reverse order of removal.
‒ To install, turn bulb holder to stop.
Hope it help!
GOOD LUCK!
Obviously, you need to get at the back of the headlight. However, on some cars this can actually require the removal of the headlight, grille, etc., etc.
Replace the head lamp cos the bulb is permanently attached & feated with the whole glass case of the head lamp. The reason why they are like that is to make sure you don't change & mix the high beam bulbs which are supoused to be on the driver's side only so that you don't flash the other drivers caming towards you from the passenger's side during night drive.
first get a bfh (big fricken hammer) and gently smash the lens and put new one in place and secure with duct tape.
The answers post by the user, for information only, UKQnA.com does not guarantee the right.